\u00a9 2021 wikiHow, Inc. All rights reserved. All tip submissions are carefully reviewed before being published, This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. You can adjust this, however, depending on your preference, as well as to suit the particular size of the door. Repurposed doors and some new slab doors may already have a hole cut for the doorknob. Hang the door and check the fit. As a DIY project, installing a new door can make a huge impact for a small investment. Then, you can attach the hardware and hang your new slab door in the doorframe. It's HARD working from home. Estimates will fluctuate depending on the style of door you choose. Circular Saw (Tool-Only) - 310550673, Carpenter Pencils (10-Pack) with Sharpener - 100522021, Holmes Workwear Black Frame with Clear Lenses Safety Glasses - 300762497, Economy Wood Chisel Set (3-Piece) - 100076202, 3 in. The one shown in the photo screws onto the side of the door and includes two hole saws. Common interior door widths are 24, 28, 30, 32, and 36 inches. This will allow you to make a clean, even cut when you plane or cut it down with a circular saw. Slab doors, also known as blank doors, include just the door and not any part of the frame. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. Next, mark the new slab (Photos 2 and 3). When marking your measurements on the slab door with a pencil, use a ruler to make sure that you draw a straight line. Follow the instructions that came with your particular lockset. 36 inches (91 cm) is the standard height for most doorknobs. Removing the old door. Place a bracket behind each of the three hinges. Simply place the new door on a flat work surface, then place the old door on top of it, making sure to align both doors in the same direction (right side up, opening to same direction, etc.). How to replace an exterior door slab. Once notching is complete, attach the new hinges to the new door. Flush doors are slab doors that are unfinished without paneling, meaning you’ll have to stain and paint them yourself. A slab door is a basic, stripped-down door that does not include a frame. There are 12 references cited in this article, which can be found at the bottom of the page. To remove the old door, start by backing the screws out of each hinge on the door slab with a screwdriver or drilling and pulling it away from the door frame. Repeat this process to cut the mortise for the other hinge. In a previous blog, we discussed the differences between pre-hung doors and slab doors.We have also outlined the steps to installing a pre-hung door.This blog will list the steps and resources you need to install a slab door. Make sure the rounded part of the latch is going the right way and attach the latch with the provided screws. Replacing a door is a project within the capabilities of most do-it-yourselfers. While the door is lying flat, install the latch portion of the new knob by tracing around it, then scoring with a utility knife and chiseling it out using the same method from Step 7, so that the latch lays flush against the door edge. If you are attaching your slab door to an existing doorframe, the mortises will already be cut and you can skip this step. Hang the door as-is into the stud frame of the home. Score the line around the hinges with a utility knife, then notch the perimeter and interior of hinge area with a hammer and chisel. Measure the width and height of the existing door and check the new slab. We used a door lock installation jig to bore holes in the slab for the latch and lever. Attaching the Door Hardware 1. However, you can find products that will make this task easier — like a jig made specifically for hinges. Cut the new door to match the … Mark the bottom of the old door on the new door with a pencil. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Use a Door Lock Installation Jig. Use a cordless gun to unscrew the hinges from the jamb. If the new door doesn’t fit, the old door can be used as a template to indicate where the new door slab should be trimmed. © 2000-2021 Homer TLC, Inc. All Rights Reserved. Then mark the hinge positions on the jamb and the stile edge of the door. If this is the case, you can skip this step. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. How to Install a Slab Door. Again, it’s really the ultimate DIY project, a completely blank design waiting for you to literally fill it all in, punch in the holes, and install the door from start to finish. If you are using both a new doorframe and a new slab door. If the new slab door is longer or wider than the old door, use a pencil to trace the shape of the old door on the new slab door. Is your idea of DIY is hiring a professional? Step 3. References. If you have the original door, re-clamp it to the new slab... 2. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Install the lockset using a Philips screwdriver. This article has been viewed 11,745 times.